Home Tips & Advice > Step-by-Step How-To's > Laying Resilient Floor Tile

Installing Resilient Floor Tile

Follow these simple instructions for laying resilient floor tile of any type. Completely read all instructions before starting the job. If any part is unclear, call or visit the store where you purchased the materials and ask for further information.

PREPARE THE BASE FLOOR

  • Start by removing all wax, grease or oil with a good, environmentally safe chemical or cleaner. Remember that adhesives will not adhere where oil or grease is a part of the base.
  • Next, plane down high spots and renail any loose boards on wood floors (see image). Any rough spots will gradually show through the floor tiles and may ruin the appearance.
  
  • If the original floor is in poor condition, it may be necessary to cover it with sturdy plywood or untempered hardboard (see image).
  • When laying a new floor, nail every 4" along the edge and 4" apart in all directions. Stagger the panels so you don't have four corners together. Start in the center of the panel and work toward the edges.
  • Use coated or ring-shanked nails, and be sure heads of the nails are even with board level.
  

START FROM THE EXACT CENTER OF THE ROOM

The first run of floor tile should be started from the exact center of the floor, so use these steps to locate the center of the room:

  • Locate the exact center on each wall and mark that center spot.
  • In rooms with offsets or irregularities, ignore the irregularities in the measuring process (see image).
  • Hold a chalk line at the center position on facing walls, as marked and snap it on the floor. The exact center will be marked at the point where the two lines cross. The example in Fig. 3 shows a room 15'10" x 14' with a slight offset.
  • To check for accuracy, measure 3' in one direction and 4' in the opposite (90 degrees) direction. When measured from true center, the distance from the 3' marking to the 4' point will be exactly 5'. If this is not the case, remeasure and rechalk each wall to find the true center. This is essential for a quality finish.

MAKE A FINAL CHECK WITH LOOSE TILE

  • Start at the center point and lay loose tiles along marked lines from center, as shown in the first image below. This procedure provides an opportunity to make adjustments if the center is not correctly marked.
  • After you have laid a full run of loose tiles along the chalk lines toward each wall (see first image below), measure the remaining distance between the edge of the last tile and the wall on each run.
  • If the distance between the last tile and the wall is less than two inches or more than eight inches, you will end up with an extremely narrow cut of tile (see second image below).
  • To correct, adjust the center line that is parallel to the wall by 4-1/2" (half a tile) closer to the wall and remark (see third image below).
  

PREPARE THE PLAN FOR TILE APPLICATION

  • Open all cartons of tiles that are to be used. Conveniently arrange them so you select tiles out of each carton on an alternating basis. This will help to prevent any noticeable color variation in tiles boxed together.
  • Next, study the tile patterns and plan your laying pattern. If the tiles are all one color, plan the pattern according to the grain (see image).
  
  • You may choose to alternate the run of the patterns (as shown), or you may decide to lay patterns in one direction. Whichever pattern you choose, it is critical to plan in advance.
  • For tiles of varying colors, plan your design carefully before applying the first tile (see image). This will influence your selection of starting tiles.
  

APPLY THE TILE CEMENT

The next step-now that you have correctly marked the center of the room and selected the tile designs and patterns-is applying the adhesive for the tile. If you are using self-sticking tile, skip this section.

  • Read all instructions for the product and follow carefully. Begin by spreading an even coat of adhesive over one-fourth of the floor. Most adhesives are applied with a notched trowel (see image), but some are still applied with a brush or roller.
  • In most cases, floor tile cement will dry to the proper consistency in about 15 minutes. However, your exact time may vary depending on humidity, temperature, etc., in the room where you are applying the tile.
  • After about 15 minutes, place your thumb onto the cement (see image). The cement should feel tacky but should not actually stick to your thumb. If it does stick, allow a little longer for proper drying.
  • When tacky but not sticky, the cement is ready for the application.
  

LAY THE FLOOR TILES

  • Start laying the tile at your markings in the center of the floor (see image). It is important that the first tile is exactly square with the lines. If the first tile is started wrong, all other tiles will also line up incorrectly.
  • Be sure each tile is butted firmly against the previous one, leaving no gaps.
  
  • Do not attempt to slide tiles into place. Lay each tile firmly into position on the cement.
  • Proceed by laying tiles alternately, according to your plan, toward each wall as illustrated in this image. This helps to counteract expansion and contraction of the tiles while enhancing the appearance.
  • To cut the border tile easily and accurately, place a loose tile squarely over the last field tile in the row (see image below). Then take another tile, butt it against the wall and mark, as illustrated. Cut the tile along the marked line using ordinary scissors. In a cold room, you should warm tiles slightly before cutting.
  
  • The cut tile will now fit securely into the border space. Be sure this tile is placed face-up and at right angles to the grain of the tile below it. This ensures the correct pattern when it is laid (see first image below).
  • When it becomes necessary to fit tiles around pipes or other obstructions, simply cut a paper pattern that fits around such obstructions and trace the pattern on the tiles. Then cut with ordinary scissors (see second image below) and place around obstruction.
  • You may want to consider adding a vinyl cove base of matching or contrasting color (see third image below) to add to the appearance and to make the floor easier to clean.
  • IMPORTANT NOTE: Do not wash your new tile floor for at least one week after installation.
  
TOOL AND MATERIAL CHECKLIST
ChalkChalk Line
MasticMastic Trowel
PlaneCement
SandpaperSteel Square
Ordinary ScissorsBrush
LevelScraper
Tape or Folding RuleHand Cleaner

back to top

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

© 2014 Ace Hardware Corporation. Ace Hardware Corporation and Ace Hardware Corporation logo are registered trademarks of Ace Hardware Corporation
HACKER SAFE certified sites prevent over 99% of hacker crime.

Add Item to To-Done List

To use this feature you must be signed-in to your account, please sign in now. If you do not have an account, please create an account to participate.

Ace Rewards

Ace Rewards is a free and rewarding membership program that lets you earn rewards with every purchase you make! Join now.